Audiophile Grade Silver Contact Output Relays repair CARVER 900 6250 2000 JR1AF
Audiophile-Grade, Silver Contact replacement output relays for CARVER The Receiver Model 900, 2000, 6200, 6250 and AVR 100 (original part typically used was JR1AF-DC24V, which is no longer manufactured).These relays also replace Denon DH2TU 24V, DH24D2-OT/M2 and 2140129001 in Yamaha, Rotel, Denon and many other receivers. If you have noise, intermittent output or complete loss of output of one or both channels, a bad output relay is likely the cause. These relays are drop-in replacements for the original parts, with specifications that significantly exceed the originals. Silver contacts provide higher current capacity, lower resistance and improved reliability. Relays are UL Recognized. Each Carver receiver uses two relays, and we recommend replacing both relays at the same time. This listing is for a PAIR of RELAYS, so you can replace both relays on your receiver. The parts are brand new and will be shipped in protective packaging. The listing is for the replacement relays only, not the complete receiver. The parts can be replaced by a person with limited soldering skills. A soldering iron, solder wick and solder are needed to replace the parts. Use standard safety precautions (wear safety glasses, unplug the unit before soldering, etc) when working on your gear. When you're done soldering, always wash your hands because solder contains lead. Please note that replacing the relays will fix the receiver only if the relay was the problem to start with! We offer the following parts for Carver MXR receivers: Trim caps and tuner ICs for intermittent or failed tuner sections http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=220643571643 Hard-to-find replacement knobs for Speaker Select, Tape Select and Tape Monitor http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=220643594640&ssPageName=STRK:MESE:IT Refurbishment kit that contains the parts most likely to fail on a Carver receiver (Relays, trim caps, power supply resistor): http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=320780840585 High Performance Voltage Regulator Assembly to replace the burnt-up-ugly-mess of resistors on the MXR-130 and -150 Noise Reduction Board: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=221262954660&ssPageName=STRK:MESE:IT Capacitor replacement kit for the MXR-130/-150 Power Supply/Amplifier board to fix power supply problems and improve audio quality: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=221255991499&ssPageName=STRK:MESE:IT See our other listings for other interesting and helpful electronic solutions! Shipping is discounted for multiple purchases! Please send us a message if you have any questions. We've worked with Carver equipment for over 30 years. We love classic audio equipment, and want to help you get the most enjoyment out of your system! We also repair Carver equipment at our location. Let us know what you need! Buyer to prepay with Paypal and pay $4.50 flat rate for shipping and professional packing (additional shipping cost outside the US). Positive feedback will be left for successfully completed transaction.
Specifications
| All Returns Accepted | ReturnsNotAccepted |
| Brand | Carver |
Audiophile-Grade, Silver Contact replacement output relays for CARVER The Receiver Model 900, 2000, 6200, 6250 and AVR 100 (original part typically used was JR1AF-DC24V, which is no longer manufactured).These relays also replace Denon DH2TU 24V, DH24D2-OT/M2 and 2140129001 in Yamaha, Rotel, Denon and many other receivers. If you have noise, intermittent output or complete loss of output of one or both channels, a bad output relay is likely the cause. These relays are drop-in replacements for the original parts, with specifications that significantly exceed the originals. Silver contacts provide higher current capacity, lower resistance and improved reliability. Relays are UL Recognized. Each Carver receiver uses two relays, and we recommend replacing both relays at the same time. This listing is for a PAIR of RELAYS, so you can replace both relays on your receiver. The parts are brand new and will be shipped in protective packaging. The listing is for the replacement relays only, not the complete receiver. The parts can be replaced by a person with limited soldering skills. A soldering iron, solder wick and solder are needed to replace the parts. Use standard safety precautions (wear safety glasses, unplug the unit before soldering, etc) when working on your gear. When you’re done soldering, always wash your hands because solder contains lead. Please note that replacing the relays will fix the receiver only if the relay was the problem to start with! We offer the following parts for Carver MXR receivers: Trim caps and tuner ICs for intermittent or failed tuner sections http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=220643571643 Hard-to-find replacement knobs for Speaker Select, Tape Select and Tape Monitor http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=220643594640&ssPageName=STRK:MESE:IT Refurbishment kit that contains the parts most likely to fail on a Carver receiver (Relays, trim caps, power supply resistor): http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=320780840585 High Performance Voltage Regulator Assembly to replace the burnt-up-ugly-mess of resistors on the MXR-130 and -150 Noise Reduction Board: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=221262954660&ssPageName=STRK:MESE:IT Capacitor replacement kit for the MXR-130/-150 Power Supply/Amplifier board to fix power supply problems and improve audio quality: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=221255991499&ssPageName=STRK:MESE:IT See our other listings for other interesting and helpful electronic solutions! Shipping is discounted for multiple purchases! Please send us a message if you have any questions. We’ve worked with Carver equipment for over 30 years. We love classic audio equipment, and want to help you get the most enjoyment out of your system! We also repair Carver equipment at our location. Let us know what you need! Buyer to prepay with Paypal and pay $4.50 flat rate for shipping and professional packing (additional shipping cost outside the US). Positive feedback will be left for successfully completed transaction.
